In doing so, any alterations performed below can be returned to it's intended state. Scripts WARNING: If you do anything with this option, ensure FLDIGI is configured to your preferences. Modem signal on left and right channels.The same name connected to your Macintosh. You should not have another sound card with "release version", so support for the TS590SG is there.Īudio, just select "USB Audio Codec", this is the name of the soundĬard within the TS590sg. Linked with the "daily snapshot" of hamlib, not with the latest It is easiest to use "Fake it", which means the VFO frequence is changed beforeĪnd after the TX cycle, rather than programming the built-in splitįortunately, the wsjt-x program you can download from the internet is VFO frequency is shifted while transmitting such that the TX audioįrequencies are always in the range 1500 - 2000 Hz such that harmonics are outside the passband. Split operation is very much recommended for wsjtx. Since the TS590SG has a "USB Data" mode, choose The baud rate must match those selected in the TS590sg for USB connection, 115200 baud is the factory default.ĬAT command for PTT switching, and check "Rear/Data" if using the soundĬard in the TRX. Note that the "Serial Port" is the SiliconLabs Chip, there should only be one in your system. This is how to configure the "Radio" section (Menu: Preferences.). USB sound cards are automatically supported these days This is easy: PortAudio is the only choice on the Mac anyway, and " USB Audio Codec" is just the name of the sound-card within the TS590sg. Modify an existing) xml file that works with your rig. With RigCAT, it is relatively straightforward to create a (or However, if your TRX is not supported by hamlib, there is little youĬan do (other than writing a new backend and contributing it to hamlib, The internal USB sound card but rather from the Microphone jacket. It is, e.g., important to use the "TX1" CATĬommand instead of "TX" or "TX0", otherwise audio is not accepted from The distinct advantage of RigCat is, that you can edit the xml fileĪccording to your needs. Note that you will, in addition, need the file TS-590S.xml. To use RigCat, uncheck the "Use Hamlib" checkbox in the "Hamlib" tab, go to the "RigCat" tab and check "Use RigCat" there. However, you are not lost in thisĬase but can use RigCAT (this is more forgiving). Than you might not find the TS590SG in the "Rig:" list (only the TS590S).ĭifferent Kenwood models return different ID numbers and this isĬhecked within hamlib, this might not work if you have the lastest rigīrand but not the latest software. If you use a precompiled fldigi program from the internet, This is fldigi linked with the latest version of Hamlib, that supports Of course, make sure that the rig is powered up and connected via USB before starting the FLDIGI program! "Audio on auxiliary" (this means: use TX1 rather than TX0 command). Use "PTT via hamlib" (this means: use CAT commands for PTT) and check Unless you have more than one SiliconLab chip connected via USB, there is only one such choice. The device name for the SiliconLabs driver is of the form /dev/tty.SLAB_USB. Theīaud rate (115200 bd) is the factory default for the USB connection, and Picture shows how I set up rig control for TS590sg with fldigi. I have not tried this hower, I prefer CAT commands for "PTT switching". Note: you can probably bring it to work without a CAT connection, since Look for " Silicon Labs VCP Driver Macintosh" on the internet and you will find it. This converter needs a driver not provided by MacOS. The rig) and a CAT interface using an USB-to-serial converter (also The USB connection with the TS590sg offers both a soundcard (within Use a good one (good shielding, ferrites) if your shack is close to the antenna. All you need is an USB cable to connect Macintosh and TS590sg. The good news is: you can download these programsįor Apple Macintosh from the internet, and they work "as is" with the I use the programs FLDIGI (mostly PSK, RTTY) and WSJT-X Digi with Apple and TS590 Digimodes with Apple Macintosh Laptop and Kenwood TS590sg
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |